Last edited by Meztigor
Wednesday, October 14, 2020 | History

3 edition of IEEE standard requirements for load tap changers found in the catalog.

IEEE standard requirements for load tap changers

IEEE standard requirements for load tap changers

  • 311 Want to read
  • 2 Currently reading

Published by Institute of Electrical and Electronics Engineers in New York, N.Y., USA .
Written in English

    Subjects:
  • Electric transformers -- Testing -- Standards

  • About the Edition

    Electrical and mechanical performance and test requirements for load tap changers installed in power transformers and voltage regulating transformers of all voltage and kVA ratings are covered.

    Edition Notes

    Other titlesStandard requirements for load tap changers., Load tap changers.
    Statementsponsor, Transformers Committee of the IEEE Power Engineering Society.
    SeriesIEEE std -- C57.131-1995.
    ContributionsIEEE Power Engineering Society. Transformers Committee., Institute of Electrical and Electronics Engineers., IEEE Standards Board.
    The Physical Object
    Paginationvi, 42 p. :
    Number of Pages42
    ID Numbers
    Open LibraryOL19646455M
    ISBN 101559375353
    OCLC/WorldCa33395824

    The Scope of this project is adoption of: IEC TC 14 Power Transformers - Tap-changers - Part 1: Performance requirements and test methods as an IEEE Standard Scope of the document being adopted: This part of IEC applies to on-load tap-changers of both resistor and reactor types, deenergized tap-changers, and their motor-drive. This part of IEC applies to on-load tap-changers of both resistor and reactor types, deenergized tap-changers, and their motor-drive mechanisms. It applies mainly to tap-changers immersed in This document references.

    Today, both the IEEE term ‘‘load tap changer (LTC)’’ and the IEC term ‘‘on-load tap-changer (OLTC)’’ are in the terminology of international standards, but the term ‘‘load tap changer (LTC)’’ is used. primarily in this chapter. Load tap changers are one of the indispensable components for the regulation. kV and Below / through / 10 kVA, Single-Phase, and / through 60 / 80 / kVA, Three-Phase Without Load Tap Changing; and / through 60 / 80 / kVA with Load Tap Changing Safety Requirement.

    Load Tap Changer Control Today A Load Tap Changer (LTC) is a mechanism internal to many transformers, especially high-voltage transformers, that can change the number of turns used in a transformer winding by selecting from a given number of available taps on that winding. It .   This paper presents a novel arcing power-based algorithm to identify failures in operations of on-load tap-changers (OLTCs). An OLTC is the solely moving part of power transformers and thus highly prone to failure. Most of the OLTC defects are originated from abnormal arcing times leading to abnormal arcing energies. The proposed algorithm utilizes the power difference between the input and.


Share this book
You might also like
What why and how?

What why and how?

Nathaniels Nutmeg (Isis)

Nathaniels Nutmeg (Isis)

Plywood.

Plywood.

Development & fabrication of a high current, fast recovery power diode

Development & fabrication of a high current, fast recovery power diode

Analysis of the Transformation Process of General Detail Sailors

Analysis of the Transformation Process of General Detail Sailors

Proceedings of the Second International Symposium on Clinical PET in Oncology, Sendai, Japan, 16-18 May 1993

Proceedings of the Second International Symposium on Clinical PET in Oncology, Sendai, Japan, 16-18 May 1993

Legal condition of women in Massachusetts in 1875

Legal condition of women in Massachusetts in 1875

Underfoot

Underfoot

Jolly Jinks song book

Jolly Jinks song book

Drowers folk-tales of Iraq

Drowers folk-tales of Iraq

KYOEI SANGYO CO., LTD.

KYOEI SANGYO CO., LTD.

Guide to Jewish history under Nazi impact

Guide to Jewish history under Nazi impact

An American transportation story

An American transportation story

IEEE standard requirements for load tap changers Download PDF EPUB FB2

For load tap changers, this standard covers both resistor and reactor types. It also covers certain aspects of the attendant tap changer motor-drive mechanism. It does not cover the tap changer control system (manual or automatic).

Purpose: The purpose of this standard is to provide standard performance and test requirements for load tap changers.

Article #: Date of Publication: 21 Sept. For load tap changers, this standard covers both resistor and reactor types. It also covers certain aspects of the attendant tap changer motor-drive mechanism. It does not cover the tap changer control system (manual or automatic).

IEEE C IEEE Standard Requirements for Tap Changers Paperback – May 4, by IEEE (Author) See all formats and editions Hide other formats and editions. Price New from Used from Paperback, May 4, "Please retry" $ $ — Paperback $Author: IEEE.

IEEE C IEEE Standard Requirements for Tap Changers STANDARD by IEEE, 05/04/ For load tap changers, this standard covers both resistor and reactor types.

It also covers certain aspects of the attendant tap changer motor-drive mechanism. It does not cover the tap changer control system (manual or automatic). IEEECIEEE Standard Requirements for Tap Changers-This standard covers electrical and mechanical performance and test requirements for tap (DETCs), also known as off-circuit tap changers, which may be operated only while the transformer is not energized.

For load tap changers, this standard covers both resistor and reactor types. Ieee C57 Standard Requirements Tap Ieee C57 Standard This part of IEC is intended to assist in the selection of tap-changers designed in accordance with IEC or IEEE Std C for use in conjunction with the tapped windings of transformers or reactors.

C - IEEE Standard Requirements for Tap Changers. standard requirements for load tap changers: ieee c design, testing, and application of liquid-immersed distribution, power, and regulating transformers using high-temperature insulation systems and operating at elevated temperatures: ieee c requirements, terminology, and test procedures for neutral grounding devices.

General types of load tap changer (LTC) mechanisms, breathing configurations, and electrical designs, described for reference for determining methods of testing and evaluating dissolved gases in mineral-based transformer oils in LTCs, are discussed and recommended in this guide.

Measurements of dissolved gas concentrations in the LTC oil are required to implement this guide. American National Standard for Transformers – kV and Below / through /10 kVA, Single-Phase, and / through 60 /80 / kVA, Three-Phase without Load Tap Changing; and / through 60 /80 / kVA with Load Tap Changing – Safety Requirements: IEEE: ANSI C ×Close.

The Infona portal uses cookies, i.e. strings of text saved by a browser on the user's device. The portal can access those files and use them to remember the user's data, such as their chosen settings (screen view, interface language, etc.), or their login data. On load tap changers Information on IEEE's Technology Navigator.

Start your Research Here. On load tap changers-related Conferences, Publications, and Organizations. Custom power devices such as on-load tap changers [2, 3] or Flexible AC Transmission Systems (FACTS) [4,5] are thus employed in distribution and transmission grids to mitigate the effects of.

A tap changer is a mechanism in transformers which allows for variable turn ratios to be selected in distinct steps. This is done by connecting to a number of access points known as taps along either the primary or secondary winding.

Tap changers exist in two primary types, no-load tap changers (NLTC), which must be de-energized before the turn ratio is adjusted, and on-load tap changers (OLTC. • (ANSI) IEEE Std C, standard general requirements for liquid-immersed distribution, power and regulation transformers • ANSI C, safety requirements kV and below / through 8,/10, KVA, single-phase, and / thro/80,/, KVA, three-phase without load tap changing; and.

PC Standard Test Code for Liquid-Immersed Distribution, Power, and Regulating Transformers - June / Antosz / expiring PC Guide for Dissolved Gas Analysis in Transformer Load Tap Changers - June / Wallach / expiring (iv) Vacuum type on-load tap changers.

(v) SFRA requirements. (vi) Apparent charge (pC). (vii) Impact of secondary generation, especially on transformers with dual secondaries.

Thorough specifications are the first step in establishing long term reliability of transformers. Specifications should cover the present and future system requirements. Get this from a library. IEEE Standard Requirements for Load Tap Changers.

IEEE and its members inspire a global community through IEEE's highly cited publications, conferences, technology standards, and professional and educational activities. IEEE, pronounced "Eye-triple-E," stands for the Institute of Electrical and Electronics Engineers.

The association is chartered under this name and it is the full legal name. Get this from a library. IEEE standard requirements for load tap changers. [Institute of Electrical and Electronics Engineers.;]. This part of IEC is intended to assist in the selection of tap-changers designed in accordance with IEC or IEEE Std C for use in conjunction with the tapped windings of transformers or reactors.

Requirements, references and definitions relevant to either IEC or IEEE Std C are given and their use is described in Clause 4.IEEE Std C for use in conjunction with the tapped windings of transformers or reactors C - IEEE Standard Requirements for Tap Changers For load tap changers, this standard covers both resistor and reactor types It also covers certain aspects of the attendant tap changer IEEE Standards Interpretation for IEEE Std C™The tap changer is usually placed on the high voltage winding as the current is lower and this minimizes the current handling requirements and stress during operation of the tap changer.

Figure a shows a schematic diagram of an off-load tap changer that requires disconnection of the transformer when the tap setting is to be changed.